Most first orders are quoted on a unit price and then invoiced on a freight number that nobody modelled. The gap is usually carton configuration: how many units go in a box, how the boxes stack on a pallet, and how much of the freight bill is air rather than product. This note sets out the arithmetic buyers can do before an order, and the points at which a carton change has to be requested.
Units per carton sets three numbers at once
Carton count is the first number a forwarder needs. It is derived from total units divided by units per carton, rounded up, and it drives the rest: how many pallets, how much loading time, and how many chances a box has to be handled. A 24-unit carton and a 48-unit carton of the same product both ship, but the 48-unit case halves the handling count and raises the weight per box, which changes what can be stacked and who can lift it.
Two constraints sit under the choice. Manual handling limits in most warehouses assume a single person can lift and stack a case without equipment, and retail distribution often specifies a maximum case weight rather than a maximum case count. Where both apply, the heavier limit wins.
Inner cartons are protection, outer cartons are structure
An inner box holds one unit; the outer case holds inner boxes. Strength belongs to the outer. A common first-order mistake is to upgrade the inner box for a premium look while leaving the outer at a single-wall grade that cannot survive a pallet stack. The cost of the extra board in the outer is small next to the cost of a returned pallet.
The test that matters is a compression test on the filled and sealed case, not on an empty one. Board grades are quoted in a way that invites comparison of the wrong number: a paper weight per square metre says little about a finished box’s stacking strength, because flute type, board combination and the amount of printing all change it.
Pallet footprint decides how much of the container you actually use
Cartons are designed to a pallet, not the other way round. The two common footprints are 1200 by 1000 mm and 1200 by 800 mm, and a carton that fits neither leaves gaps that no amount of careful loading recovers. Overhang is not a solution: a pallet that overhangs its base loses strength in the corners, which is where damage begins.
Stack height is the other half. Pallet height including the pallet itself is what the container’s internal height constrains, and the last few pallets in a container are the ones that end up short-loaded when the arithmetic is done late.
Volumetric weight is the line most often missed
Air and express freight are charged on the greater of actual weight and volumetric weight, the latter derived from the carton’s dimensions using the carrier’s divisor. A light product in a large case is billed as if it were heavy. The practical consequence is that reducing a carton by twenty millimetres on one side can change a freight quote, while reducing the product cost by a few cents does not.
On sea freight the same dimensions matter differently: containers are sold by volume, so the number that counts is cubic metres per carton multiplied by carton count, plus the unusable space created by pallet gaps and stack limits. Buyers comparing FOB quotes between two suppliers are often comparing two different carton configurations, which is why the wholesale FAQ asks for carton dimensions before a landed cost is calculated.
When a carton change has to be booked
A carton change is a print job, a die revision and a packing-line change. It needs to be requested before the artwork is signed off, not after: quantities per carton appear on the carton mark, the packing list and usually the label’s outer face, so changing them later reopens the label rather than only the box. Where an order is already in production, the honest answer is that the change applies to the next run.
The private label route sets this sequence out in order, and the factory page describes how packing is recorded per batch here. Buyers comparing formats before a quote can see net weights on the body care shelf, since net weight per unit is what makes the units-per-carton arithmetic work in the first place.
Three lines to put in the enquiry
Give the units per carton you want, the maximum case weight your warehouse or retailer accepts, and the pallet footprint your market uses. Those three lines turn a unit price into a landed number, and they cost nothing to specify at the enquiry stage rather than after the deposit.
Related
Leave a Reply