Repackaging vs Private Label: Which One Fits Your Volume

Two routes get a brand onto a shelf: repackaging goods that already exist, or having a range made under your own label. They look similar on a price list and behave very differently once volumes, timelines and liability are involved. This note sets out where the line falls, so the choice can be made on arithmetic rather than on preference.

What each route actually is

Repackaging means taking a finished product that is already manufactured and sold — often under a stock or house brand — and putting it into your own packaging, or over-labelling the existing pack. The formula, the fill and usually the container stay as they are.

Private label means a product made for you: your brand on the pack, and depending on the arrangement your formula, your fragrance, your fill weight and your container. The factory runs it as your order rather than as stock.

There is a middle route worth naming, because much of the confusion lives there: a stock formula in a stock container, but printed or labelled with your brand at a defined minimum. That is closer to private label on the compliance side and closer to repackaging on the cost side.

The differences that actually cost money

  • Minimum quantity. Repackaging can start low because the goods already exist. Private label is bounded by the batch the line has to run — which is why a first order usually sits at a defined minimum rather than at whatever number you would prefer.
  • Artwork and approval. On a stock product the label is set. On your own label every element has to be written, checked against the destination market and approved before print. That work is real and it sits on your side of the table unless it is explicitly contracted out.
  • Time to first shipment. Repackaging moves within days if stock is available. Private label adds formula confirmation, samples, stability and compatibility work, print, then filling. The preparation window quoted for a private label run does not include the technical work that precedes it.
  • Who is responsible. Whoever places the product on the market carries the obligation, and in the EU and UK that means a named responsible person established in the market. Repackaging does not avoid this — it relocates the question, because re-labelling can make you the one placing it.
  • Exit cost. If repackaging stops working, you stop ordering. If a private label range stops working, you may be holding printed packaging with your brand on it, which has no resale value to anyone else.

The label obligations themselves are set out in what must appear on a cosmetic pack, and the EU distributor requirements are covered in what an EU distributor must hold.

Choosing on volume

The decision usually turns on a single number: how many units you can commit to per run, and how confident you are that they will sell.

Below a few hundred units per reference, repackaging is normally the only route that makes sense, because a private label batch would leave you holding stock you cannot move. Between a few hundred and a low four-figure run, the middle route — stock formula under your brand at the factory minimum — is often the practical answer: it buys brand presence without paying for development.

Above that, private label starts to win on unit economics: the per-unit cost of development is spread across a real order, and you gain control of the things that differentiate a product — texture, fragrance, fill, container.

A second number matters as much as the first: how many references. A range of twenty references at low volume each is a different problem from two references at high volume, and the cheapest route is usually to consolidate. This is worked through in how many SKUs to launch with (covered separately, since the arithmetic differs by category).

What to ask before deciding

  • Can I see the exact formula and fill I would be repackaging, and is the container fixed?
  • At what quantity does the supplier switch from stock to a run made for me?
  • Who writes and approves the label copy, and against which market?
  • What technical work is required before a first private label shipment, and how long does it take?
  • If I move from repackaging to private label later, what changes — pack, formula, or both?
  • What do I own if the arrangement ends: artwork, plates, unused packaging?

The last question is the one most often skipped, and the one that decides how expensive a wrong guess turns out to be.

How the two routes meet

They are not mutually exclusive. A common pattern is to open a market with repackaged or stock-formula goods, measure sell-through at low risk, then move the references that work onto a private label run. The information gained in the first phase — which reference sells, at what price, through which channel — is what makes the second phase’s minimum quantity a calculated commitment rather than a bet. A FATAZEN product sold in its own printed tube is the Floral Hand Cream.

Our private label process describes what a first run involves, and the wholesale FAQ covers quantities, preparation time and terms. If you are preparing a first brief, how to write a private label brief a factory can quote sets out what the factory needs in order to price accurately rather than approximately.

Related reading

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *