A complaint about a batch is a sequence of checks, not an argument. The factory that answers first with a conclusion and later with evidence usually ends up revising the conclusion. This page sets out the order the checks run in, what the buyer has to send before any of them start, and what the reply should contain while the investigation is still open.
What the complaint has to contain first
Six facts decide whether a complaint can be investigated at all: the batch number from the label, the quantity affected against the quantity delivered, the date the goods were received and the date the problem appeared, the storage conditions since arrival, photographs, and what the buyer is asking for — replacement, credit, or an explanation.
Without the batch number there is nothing to compare against, because the retention sample is filed under that number. Without the affected quantity there is no way to tell a single damaged carton from a production fault. Without the appearance date and storage conditions, a temperature-related separation reads exactly like a formulation fault.
The retention sample is compared before anything else
A factory that runs batch records keeps sealed retention samples per batch. The first check is a side-by-side comparison of the buyer’s unit against that sample: colour, odour, texture, fill level, and whether the container and closure are the ones that were approved.
This comparison answers one question and no more — whether the batch left the factory in the state the buyer is now describing. If the retention sample shows the same separation or the same colour drift, the cause is upstream of shipping. If the sample is intact and the buyer’s unit is not, the cause is downstream: transport, storage, or time at the destination.
The four photographs that answer most questions
An outer carton showing the printed batch code and the shipping mark. A single unit with the label facing the camera, so the batch code on the unit can be read against the carton. A close-up of the defect with something for scale in frame. And a wide shot of the remaining stock, so the affected quantity can be counted rather than estimated.
These four, taken together, let the factory check the batch code against its own packing list without asking for a second round of pictures. A complaint that arrives with one blurry photo costs a day before the first real check begins.
Where a defect can originate, and how to tell them apart
Formulation or compounding faults show up across the whole batch. If the retention sample is affected, every unit from that batch is affected, and the response is a batch-level decision.
Filling and packaging faults show up in a pattern: a run of units with low fill, a set of caps that did not seal, a label applied off-centre on one part of the line. The retention sample is usually intact, because the sample was pulled from a different point in the run.
Transport and storage faults show up by position: one pallet, one corner of a pallet, or everything that sat in one container. Heat exposure leaves containers deformed or contents separated; freezing leaves texture that does not recover at room temperature. The pattern, not the defect itself, identifies the cause.
What to reply within 24 hours
Three sentences are enough while the investigation is open. Acknowledge the batch number and the affected quantity as the buyer stated them, so both sides are working from the same figures. State which check is running and when the answer will come. State what happens to the affected units in the meantime — held, quarantined, or released for sale at the buyer’s own risk.
What does not help is a reply that offers a replacement before the cause is known. If the cause is storage at the destination, the replacement fails the same way and the second complaint is harder to resolve than the first.
Replacement, credit, or rework
A replacement lot is the right answer when the buyer needs stock and the cause is confirmed upstream. A credit note is simpler when the affected quantity is small relative to the freight cost of reshipping. Rework — relabelling, repacking, or reworking fill levels — only applies when the product itself is sound and the fault sits in the packaging.
Whichever route is chosen, the credit or replacement quantity has to be tied to the counted affected units, not to the buyer’s first estimate. The counting method is worth agreeing in the reply, before the units are destroyed or returned. Terms for credit notes and their place in the payment schedule are set out on the wholesale FAQ.
Change control before the next order
A complaint that closes without a change to the process will reopen. The minimum record is a corrective action naming what changed — a filling setting, a closure torque value, a carton specification, a storage instruction added to the shipping documents — plus the batch number that will be checked to confirm the change held.
When the fix touches the formula or the packaging, it becomes a specification change, and specification changes are what the private label process exists to control: a new artwork version, a new approval, and a new retention sample filed under the new batch. The facility records that a buyer can ask for in support of that change are listed on the factory page. Distributors handling complaints on behalf of their own customers will usually want the corrective action in writing, since the distributor terms put the first-line response on them.
Related
How to Read a Batch Code on a Skincare Label
When a Shipment Arrives Short: Claims Before You Reorder
Export Documents for a First Cosmetics Shipment
Leave a Reply