A first order carries more financial risk than any repeat order that follows it. The buyer has not seen the goods, the factory has not seen the payment history, and neither side has a track record to fall back on. Payment terms exist to split that risk, and they are usually negotiated before the deposit is sent rather than after. This note sets out how the split is normally structured, which documents release each stage, and the points where buyers and suppliers most often disagree.
Why terms are settled before the price is final
A unit price is only half of a commercial offer. The payment structure decides when cash leaves the buyer and when it reaches the supplier, and that timing changes the real cost of the order. Two quotations at the same unit price can differ by weeks in cash exposure. For that reason a quotation that lists only a price per piece, without payment stages and the documents attached to each, is not yet a complete offer. The quotation checklist sets out the fields that should appear before a buyer compares suppliers.
The three stages of a first-order structure
Deposit before production
The deposit covers materials and reserves production capacity. It is normally the stage that converts a quotation into a booking, and it is usually triggered by a signed order confirmation or a proforma invoice rather than by a verbal agreement. Once the deposit clears, material purchasing and production scheduling start; the lead time quoted to the buyer is counted from that point, not from the date of the enquiry.
Production and the inspection window
Between deposit and balance there is a period in which the buyer can still influence the outcome. Sample approval, artwork checks and any pre-shipment inspection fall here. Buyers who leave inspection until after the balance is paid lose most of their leverage, because the goods are already finished and packed. Booking the inspection window early is cheaper than disputing a finished batch.
Balance before release
The balance is normally due once the goods are complete and the shipping documents are ready, and before the goods leave the factory or the freight forwarder releases the bill of lading. What counts as “ready” differs between suppliers, so the wording matters: finished and packed, inspection passed, documents issued, or container loaded. Each of those is a different moment.
Which documents release the balance
Most disputes about the balance are really disputes about documents. The usual set is a commercial invoice, a packing list, and a bill of lading or forwarder receipt. Certificates of analysis and test reports may also be attached where the buyer asked for them. Buyers should ask, in writing, which of these they will receive before paying the balance rather than after. The Incoterms note explains how the chosen term changes who holds the documents at each point.
What shifts the split
Four factors usually move the percentages and the timing. Order value matters because a small first order often carries a higher deposit share to cover fixed setup. Custom tooling matters because moulds and print cylinders are paid for once and used for many runs. Whether the buyer is new to the supplier matters, since a first order has no payment history behind it. And the destination matters, because longer transit and customs clearance extend the period in which the buyer carries risk on goods they have already paid for.
Terms that need to be in writing
Four items are worth putting in the order confirmation even when they feel obvious. The currency and the bank charges at each end. The date from which lead time is counted. What happens if the buyer delays the balance, and what happens if the supplier delays production. And whether the deposit is refundable if artwork approval fails and the order is cancelled before materials are cut. Suppliers who answer these in writing before the first invoice tend to have fewer disputes later; the wholesale FAQ covers the questions buyers ask most often at this stage.
Where friction usually appears
Three patterns account for most first-order disagreements. The first is a lead time quoted from the enquiry date but counted from the deposit date. The second is a balance requested against photographs rather than documents. The third is a deposit treated as non-refundable in every circumstance, including cancellation before production begins. None of these is unusual in the market, and all of them are cheaper to resolve in the quotation than after the goods are made.
What a buyer can prepare in advance
Buyers who arrive with three things settled move faster: an approved artwork file, a confirmed fill size, and a nominated inspection option. Those three remove most of the back-and-forth that delays a first order. The private label section describes the sequence from brief to shipment, and the factory page lists the production steps that sit between deposit and balance.
Related
Private Label Quotation Checklist
Incoterms for Cosmetic Buyers: FOB, CIF and Landed Cost
Sample Approval: What to Check Before You Sign Off
Leave a Reply